RSA Power Wire
The 12 gauge red wire on the 2-pin
power plug is the 12 Volt positive power wire. It must be connected
to the positive terminal of the battery to provide a power source
with a low voltage drop and low noise. Do not make the power connection
at the fuse block or any point other than the battery. Improper
power sources can reduce output and cause distortion.
The fuse holder should be connected to the battery's
positive terminal. The fuse is designed to prevent fire or damage
to your car, should the battery wire short to ground. Wait to insert
the fuse into its holder until all power connections have been made.
If it is necessary to lengthen the battery wire,
add the required length between the amplifier and the fuse holder,
not the fuse holder and the battery. Use 12 gauge or larger to extend
the battery wire. It is best to use as short a wire as possible.
Be sure you DO NOT run the power wire next to
the input cables of the amplifier, as this may induce noise.
Avoid running the power wire near the radio's
antenna or power leads, or near sensitive equipment or harness.
The power wire carries substantial currents and could induce noise.
DO NOT substitute the
15 amp fuse included with the Amplified Bazooka with anything other
than the same fast blow current rated fuse. Substitution or deletion
will void the product's warranty and may cause damage to you car
or the amplifier.
RSA Ground Wire
The 12 gauge black wire on the 2-pin
power plug is the negative ground wire. It must be connected directly
to the vehicle chassis near the amplifier.
We do not recommend extending the ground wire
in any installation, as this can cause unwanted ground loops.
The ground point in the car should be a piece
of chassis metal that is welded to the main body of the vehicle.
Painted surfaces should be scraped or sanded clean before the ground
lug is bolted down. (Cover the bare metal area with paint or grease
to prevent rust.)
RSA Remote Turn
The Orange wire on the Amplified Bazookas'
14-pin Molex Mini-fit Jr. connector is the remote turn on wire.
You have several options for connecting the Remote Turn-on.
- 12 Volt Remote from source unit with an on\off switch
- 12 Volt Remote from source unit
- 12 Volt Accessory or ignition with an on\off switch
- 12 Volt Accessory or ignition
- RSA's built-in Auto Turn-On Feature
Turn-On Option One
Using an on/off switch connect
the ORANGE Remote Turn On to one side of this switch, with the other
side connected to the source unit's "Accessory," Auto-Antenna,"
or "Remote" lead -- any of which will supply 12 Volts
positive when the source is turned on.
The on/off switch allows you to demonstrate
to others the difference the Amplified Bazooka makes in your system,
or to turn it off whenever you desire.
Turn-On Option Two
If you don't want the use of the on\off switch you may hook up the ORANGE Remote Turn On wire to
the source unit's "Accessory," Auto-Antenna," or
"Remote" lead -- any of which will supply 12 Volts positive
when the source unit is turned on.
This will allow the Amplified Bazooka to be turned
on and off with the source unit.
Turn-On Option Three
If the source unit does not have an
Auto-Antenna lead (or if the Auto-Antenna goes down during tape
operation) you can connect the Amplified Bazookas' ORANGE Remote
Turn-On wire to one terminal of the on/off switch and the Switch's
other terminal to an accessory or ignition point at the vehicle's
In this configuration, the Amplified Bazooka
will be on whenever the ignition and the on/off switch are both
This method may allow noise or turn-on and turn-off
transients to become amplified when the source unit is not in use.
If this occurs, simply turn off the on/off switch when the source unit is not in use and this noise will be
RSA Remote Turn-On
If you don't want the use of the on\off switch and the source unit does not have an Auto-Antenna
lead, you may hook up the ORANGE Remote Turn-On lead to an accessory
or ignition point at the vehicle's fuse block.
This will allow the Amplified Bazooka to be turned
on by the vehicles' ignition, and remain on as long as the key is
in the accessory of run position.
This method may allow noise or turn-on and turn-off transients to
become amplified when the source unit is turned on, off or whenever
it is not in use and the vehicles' ignition is on, and therefore
may prove to be unsuitable for your application.
Turn-On Option Five
The Amplified Bazooka has a built-in
Auto Turn-On Feature.
If you choose to use this feature, the Amplified
Bazooka will turn on automatically whenever there is music present
at the inputs (high-level or low-level inputs).
Please take notice of the On/Off Jumper Clip
located on the back of the amp, right above the harness receptacle.
SAS ships the Amplified Bazooka with this Jumper
in the Off Position.
To use the Auto Turn-On Option the Jumper must
be in the On Position. The Jumper Clip must be lifted off of the
middle and right hand pins and reinserted across the left hand and
middle pins to enable the Auto Turn-On feature. This can be done
easily with a pair of needle nose pliers. With the Jumper in the
On Position, the Amplified Bazooka will turn on automatically when
it senses any music.
The ORANGE wire should not be connected to anything
if this feature is being used. Be sure to insulate the end of the
ORANGE wire so that it will not short to ground, as this may damage
the Amplified Bazooka.
Input Signal Connections
If the source unit has only speaker
outputs, use the Amplified Bazooka's high-level inputs. If the source
unit has both high and low level outputs, we recommend using the
high level inputs over the low level inputs, due to the configuration
of the RSA's balanced input circuit. NEVER
USE BOTH high and low-level inputs at the same time!
Connect the GREEN wire from the 14-pin Molex
plug of the Amplified Bazooka to the source units left (+) positive
speaker output. Connect the GREEN W/BLACK stripe wire of the plug
to the source units left (-) negative speaker output. Connect the
GRAY wire of the plug to the source units right (+) positive speaker
output. Connect the GRAY W/BLACK stripe wire of the plug to the
source units right (-) negative speaker output. If the source unit
has both front and rear speaker outputs, use only one set of speaker
outputs for the high-level input of the Amplified Bazooka.
- Connecting one of the Amplified Bazooka's High-level Input channels
out of phase electrically with the other High-level Input channel
may cause damage to the amplifier's input section. NEVER DO THIS!
If you are not sure of the polarity
of the wires that you are tapping into, connect one channel first
and check it by turning on the unit and listening to it.
If there is no output, turn off the unit and
reverse the polarity of the inputs wires.
If it still has no output, you have other problems,
Check all connections. If it sounds correct, turn off the unit and
connect the other channel.
Turn on the unit again and listen to it, if the
output increases, you are connected correctly.
If the output drops or is reduced, turn off the
unit immediately as it is not the correct polarity and may damage
Reverse polarity of one channel and check it
again, the output should increase which indicates you have the connections
If your source unit only has low-level
RCA phono jack output, use only the low-level inputs of the Amplified
Connect the low-level RCA phono jack inputs of
the Amplified Bazooka to the source with a shielded RCA patch cord.
To avoid possible noise problems, be sure to run the patch cord
away from all power wires and factory wire harnesses.
NOT make any connections to
the Green and Gray high level wires of the Amplified Bazooka and
be sure these wires are insulated to avoid the possibility of a
Optional High-Level Output
The Amplified Bazooka has provisions
for high level output to a second Bass Tube. If you want to use
this feature, you can purchase a Bazooka 4 ohm passive unit from an authorized
Be sure to use a 4 ohm passive unit that is the same
size as you amplified unit. This is necessary because different
size woofers have different efficiencies. These efficiency differences
result in the two woofers playing at different volume levels, making
it difficult to adjust the system to the desired sonic quality.
Located the BROWN and YELLOW wires on the 14-pin
Molex plug, connect the BROWN wire to the RED terminal of the 4 ohm passive
unit, and the YELLOW wire to the BLACK terminal of the 4 ohm passive unit.
The Amplified Bazooka is now operating under
a 2 ohm load and is delivering a total of 120 watts.
Adjusting the RSA's Crossover
The built-in crossover on the Amplified Bazooka is a 12dB per octave electronic low pass filter, it has a 50Hz to 250Hz variable crossover point. Select the crossover point that best suits your system design. Set the potentiometer labeled XOVER to the point you selected, 50Hz being all the way to the right (clockwise) and 250Hz being all the way to the left (counter-clockwise). When you have set the crossover, proceed to the next step.
Adjusting the RSA's Level Control
Locate the potentiometer labeled LEVEL. This is the level control. Start with the level control turned all the way to the right (clockwise). The bass should be off or very low at this point. Turn up your head unit until the sound form the existing speakers starts to clip or distort. This is the point in your system where you will get maximum volume with the least amount of distortion. With the head unit at this point, turn the level gain control up slowly until the bass volume blends well with the existing high frequency speakers. This should be the proper setting for the level gain control. Now that the level is set, you may want to go back to the crossover control and adjust the crossover point by ear to meet the desired sonic quality of your system design.