Go Back   Club Bazooka > Search Forums

Notices

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: heavyduty
Forum: Amplified Tube Subwoofers Yesterday, 07:31 PM
Replies: 4
Views: 51
Posted By heavyduty
Re: Need help installing Bazooka BTA10100FHC BT in 2011 Dodge Charger

I am not totally sure, but I was under the impression that you always have to run a 12v to the battery to energize the tube. But I think with the tubes under 100 watts, you don't have to do this...
Forum: Amplified Tube Subwoofers Yesterday, 07:27 PM
Replies: 4
Views: 32
Posted By heavyduty
Re: Conundrum

If you are experiencing a 20 db drop after 60 hz, which is roughly the equivalent of an 18db filter, you are suffering from an air flow problem (or an incorrectly set filter). However, you have said...
Forum: Amplified Tube Subwoofers Yesterday, 04:04 PM
Replies: 4
Views: 32
Posted By heavyduty
Re: Conundrum

If I were having a significant problem with bass output of the Tube, I would start with looking at how the Tube is mounted. Is the Tube in the optimum location for corner loading? How far from the...
Forum: Component Amplifiers 01-22-2015, 09:33 PM
Replies: 5
Views: 64
Posted By heavyduty
Re: EL2150 2 Channel 750 Watt Peak

https://www.southernaudioservices.com/ELA-BCM-Bass-Control-Module-for-EL-Series-Amplifer-P209.aspx
Forum: Passive Tube Subwoofers 01-22-2015, 09:31 PM
Replies: 10
Views: 119
Posted By heavyduty
Re: help me find the right bazooka for my amp

Yes, it is done at the speaker terminal at the back of the Tubes.
Forum: Component Amplifiers 01-21-2015, 07:47 PM
Replies: 5
Views: 64
Posted By heavyduty
Re: EL2150 2 Channel 750 Watt Peak

Click the following link for the original owner's manual for the ELA2150.

http://www.bazooka.com/pdf/current/el_amplifier_manual.pdf
Forum: Component Amplifiers 01-21-2015, 06:50 PM
Replies: 5
Views: 64
Posted By heavyduty
Re: EL2150 2 Channel 750 Watt Peak

Technically, the bridged output at 4 ohms mono, is 460 watts RMS. So, the answer to your theoretical question, is the ELA2150 capable of a 2 ohm bridged output, the answer is a very simple, no.
Forum: Amplified Tube Subwoofers 01-20-2015, 11:34 AM
Replies: 3
Views: 64
Posted By heavyduty
Re: Help!

Yes, the green LED is supposed to light up once the Tube is powered on.

Did you do something wrong? Probably not, since the Tube is working. However, for giggles, switch the switched +12v from...
Forum: Amplified Tube Subwoofers 01-20-2015, 11:27 AM
Replies: 4
Views: 51
Posted By heavyduty
Re: Need help installing Bazooka BTA10100FHC BT in 2011 Dodge Charger

What factory system do you have in the Charger? Be sure to list all of the features of the system as well.
Forum: Marine Audio 01-20-2015, 11:26 AM
Replies: 1
Views: 60
Posted By heavyduty
Re: 100 watt or 250 watt tube?

The benefit will be a higher volume, due to the fact that you have 2.5 times more power. As a result, yes, it will require more amperage, however, it is still not a huge drain on the power system,...
Forum: Amplified Tube Subwoofers 01-15-2015, 10:11 PM
Replies: 160
Views: 57,243
Posted By heavyduty
Re: FAST-9999 Installaton Instructions

You are most likely dealing with an installation issue, based on what I am reading, as well as if I am clearly understanding what I'm reading.

To begin, the red, constant 12v power wire of the...
Forum: Passive Tube Subwoofers 01-15-2015, 09:54 PM
Replies: 7
Views: 95
Posted By heavyduty
Re: Vertical mount?

You got it.
Forum: Passive Tube Subwoofers 01-15-2015, 04:19 PM
Replies: 10
Views: 119
Posted By heavyduty
Re: help me find the right bazooka for my amp

You will have to wire the voice coil in series, to obtain an impedance of 8 ohms, and then wire each Tube to the amplifer terminals, resulting in a total final impedance of 4 ohms.
Forum: Passive Tube Subwoofers 01-15-2015, 03:18 PM
Replies: 10
Views: 119
Posted By heavyduty
Re: help me find the right bazooka for my amp

As for wiring to the amp, wire each Tube's voice coils in parallel, and then wire each Tube to the one set of amplifier terminals. Or, you can even wire both terminals of the positive and negative...
Forum: Passive Tube Subwoofers 01-15-2015, 03:14 PM
Replies: 10
Views: 119
Posted By heavyduty
Re: help me find the right bazooka for my amp

No, I do not recommend a pair of BT1024. And here is why - you are looking at a total impedance of 1 ohm or 4 ohms. (It is simple math - parallel is wiring the positive and positive/negative and...
Forum: Passive Tube Subwoofers 01-15-2015, 11:28 AM
Replies: 7
Views: 95
Posted By heavyduty
Re: Vertical mount?

No, not neccesarily. While it does sound like a big difference in power, and it is, these are for the bass notes, which just so happen to need more power, to make a presence. The size of the Tube's...
Forum: Passive Tube Subwoofers 01-14-2015, 06:11 PM
Replies: 7
Views: 95
Posted By heavyduty
Re: Vertical mount?

Max power for the 6" Tube is 125 watts. However, just choose the BT6028 DVC Tube. Wire the voice coils in parallel, and then wire the Tubes in parallel. You will end up with the same 2 ohm load,...
Forum: Passive Tube Subwoofers 01-14-2015, 03:22 PM
Replies: 10
Views: 119
Posted By heavyduty
Re: help me find the right bazooka for my amp

Hot from the desk of the Tube guru, Geneh, an electronics mad man, "Get two BT1028dvc and wire each coil in parallel and then wire the 2 subs in parallel to give you 600 watts at 2 ohms. You will get...
Forum: Passive Tube Subwoofers 01-14-2015, 03:19 PM
Replies: 7
Views: 95
Posted By heavyduty
Re: Vertical mount?

Yes, it will absolutely work. With 300 watts at a 2 ohm mono load, go with a pair of BT6014's (4 stands for ohm impedance. Wired in parallel will be a 2 ohm load).
Forum: Passive Tube Subwoofers 01-13-2015, 11:41 AM
Replies: 10
Views: 119
Posted By heavyduty
Re: help me find the right bazooka for my amp

To be perfectly honest, there really is only one 10" model, the BT10. The difference is in the ohms (4 or 8), and single or multiple voice coils. This allows the user to configure multiple Tubes...
Forum: Passive Tube Subwoofers 01-05-2015, 07:48 PM
Replies: 1
Views: 163
Posted By heavyduty
Re: Best amp option for bt1224dvc

Any amplifier with 250 watts per channel, or an amplifier that is stable in a 2 ohm mono load, with an output of 500 watts. Look for an adjustable subsonic filter, or a fixed subsonic filter, at...
Forum: General Chat 01-02-2015, 04:26 PM
Replies: 3
Views: 354
Posted By heavyduty
Re: NOS bazooka bass tube

Do a quick Google search, or visit a reputable online retailer. If you want to go the used route, eBay is always a good choice.
Forum: General Chat 12-31-2014, 01:16 PM
Replies: 3
Views: 354
Posted By heavyduty
Re: NOS bazooka bass tube

Look for an amplifier with a 150 (minimum)-300 watt (maximum) output at a 4 ohm mono load. Also look for a model with a subsonic filter that is set, or can be set to 35 or 40hz. Absolutely no lower...
Forum: Amplified Tube Subwoofers 12-31-2014, 01:11 PM
Replies: 2
Views: 439
Posted By heavyduty
Re: Wiring Harness Compatability

Yes, they use the exact same wiring harness.
Forum: Amplified Tube Subwoofers 12-28-2014, 03:52 PM
Replies: 1
Views: 208
Posted By heavyduty
Re: What is it

These are passive Tubes. Posting pictures of the Tubes will allow me to identify them.
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 03:22 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Template-Modifications by TMS
bazooka.com
SAS, BAZOOKA, BASS TUBES, and LISTEN TO YOUR EARS are registered trademarks of Southern Audio Services, Inc.