Go Back   Club Bazooka > Search Forums

Notices

Showing results 1 to 25 of 500
Search took 0.68 seconds.
Search: Posts Made By: heavyduty
Forum: Amplified Tube Subwoofers 11-11-2014, 10:42 AM
Replies: 2
Views: 76
Posted By heavyduty
Re: BTA810FHC BT problem

Relocate the remote turn-on wire to a switched +12v source.
Forum: Amplified Tube Subwoofers 11-07-2014, 03:46 PM
Replies: 2
Views: 89
Posted By heavyduty
Re: BT8250 Outputs?

The High Level Output wires, are for adding an optional BT1014. This drops the overall system impedance to 2 ohms mono. Yes, the internal amplifier of the 8250D powers both. It is not a signal...
Forum: Passive Tube Subwoofers 10-20-2014, 03:50 PM
Replies: 1
Views: 175
Posted By heavyduty
Re: how to hook up two different voice coil tubes?

How to wire the pair of Tube's, will be dependent on what models you currently have. What version of the SVC and DVC do you have?

As for the terminals, the Tube with 2 terminals, is the SVC...
Forum: Amplified Tube Subwoofers 10-15-2014, 04:35 PM
Replies: 5
Views: 210
Posted By heavyduty
Re: need help hooked every thing up not working?

My first thought would be the splices that you have made. I am hoping that you have done more than strip some insulation, twist the wires together, and wrapped with electrical tape. As for the rest...
Forum: Amplified Tube Subwoofers 10-13-2014, 10:55 AM
Replies: 10
Views: 233
Posted By heavyduty
Re: Hoping someone can help me

Connect the LOC using all 4 wires, both the left and right channels.

You will not be using one channel of the LOC, you will be using them both. Which means you will be using a pair of RCA...
Forum: Amplified Tube Subwoofers 10-08-2014, 09:53 AM
Replies: 1
Views: 98
Posted By heavyduty
Re: BTA10250D does not power up

Call Customer Service with receipt and Tube serial number in hand, and ask for a RTA, explaining what the problem is. Customer Service will explain the options for repair and/or replacement. ...
Forum: Amplified Tube Subwoofers 10-07-2014, 12:53 PM
Replies: 1
Views: 77
Posted By heavyduty
Re: Help wit bazooka BTA8250D

To begin troubleshooting, the first thing you will need is a multi-meter. You will need to verify that you do have +12v at the Tube, both on the constant power wire, as well as the switched +12v...
Forum: Amplified Tube Subwoofers 10-03-2014, 11:00 AM
Replies: 6
Views: 150
Posted By heavyduty
Re: Harley Street Glide Powered Tube Install

A single 3" or 4", whichever you feel most comfortable with doing. No, there is no downside to 2 - 2" ports versus a single 4" port. All we are trying to do here is create airflow to eliminate...
Forum: Amplified Tube Subwoofers 09-30-2014, 01:20 PM
Replies: 6
Views: 150
Posted By heavyduty
Re: Harley Street Glide Powered Tube Install

Yes, the HD-SIK is designed to be used with the Bazooka amplifier.
Forum: Amplified Tube Subwoofers 09-30-2014, 11:55 AM
Replies: 1
Views: 86
Posted By heavyduty
Re: can i connect my powered subwoofer to another aftermarket amplifier?

1).By connecting to another amplifier, I assume you mean connecting to the speaker outputs of the new amplifier. If so, then yes.

2).No, it does not mean you can disconnect the positive power...
Forum: Amplified Tube Subwoofers 09-30-2014, 11:50 AM
Replies: 6
Views: 150
Posted By heavyduty
Re: Harley Street Glide Powered Tube Install

No, you will not need to add a capacitor. The amperage draw of the BTA6100 is quite low.

Be sure to check out the FAST-HD-SIK for the installation and mounting of the Tube. It will also take...
Forum: Amplified Tube Subwoofers 09-23-2014, 12:12 PM
Replies: 10
Views: 233
Posted By heavyduty
Re: Hoping someone can help me

No, that is not what happens. When the Tube is connected, and the vehicles system is turned on, the audio system is sensing an impedance issue with the subwoofer. As such, the system intially turns...
Forum: Amplified Tube Subwoofers 09-23-2014, 12:08 PM
Replies: 157
Views: 54,259
Posted By heavyduty
Re: FAST-9999 Installaton Instructions

The green LED should turn off when the vehicle is off. The green LED indicates that the turn-on circuit has power.
Forum: Amplified Tube Subwoofers 09-23-2014, 11:23 AM
Replies: 10
Views: 233
Posted By heavyduty
Re: Hoping someone can help me

No apologies needed. No one should ever give you a hard time for asking a valid question, especially if you are geniunely interested in learning. A LOC is a Line Output Converter. It takes the...
Forum: Amplified Tube Subwoofers 09-23-2014, 11:09 AM
Replies: 157
Views: 54,259
Posted By heavyduty
Re: FAST-9999 Installaton Instructions

Identify the constant +12v of the harness, as well as the switched +12v of the harness. Connect the red wire of the FAST to the constant +12v, and the blue/white wire of the FAST to the switched...
Forum: Amplified Tube Subwoofers 09-23-2014, 11:08 AM
Replies: 1
Views: 149
Posted By heavyduty
Re: is RCA sound quality same a rear speaker wire tap?

No, there will not be a gain in sound quality, in fact, there will most likely be a loss due to the 2.5v of the low level. Using high level outputs is using a VERIFIED high voltage signal, the...
Forum: Amplified Tube Subwoofers 09-23-2014, 10:59 AM
Replies: 10
Views: 233
Posted By heavyduty
Re: Hoping someone can help me

This may very well be an impedance issue. The fix is to install an LOC into factory subwoofer leads.
Forum: Amplified Tube Subwoofers 09-16-2014, 03:39 PM
Replies: 2
Views: 169
Posted By heavyduty
Re: Wire Size Issue

The amperage draw of the BTA Line is quite small, as such, the fuse holder with 18 gauge pigtails, attached to a 16 gauge or larger power wire (as directed in the manual), will have absolutely no...
Forum: Amplified Tube Subwoofers 09-10-2014, 01:50 PM
Replies: 3
Views: 208
Posted By heavyduty
Re: Low Level Input Question

No, you will need to purchase y-adapters to make the connection.
Forum: Amplified Tube Subwoofers 09-09-2014, 02:58 PM
Replies: 3
Views: 159
Posted By heavyduty
Re: Consant Even Volume

Please see my response to your other post.
Forum: Amplified Tube Subwoofers 09-09-2014, 02:57 PM
Replies: 8
Views: 2,529
Posted By heavyduty
Re: Jeep Wrangler

Great. After the connections are made, and IF, you run into the Tube powering on, followed by the entire system powering off, you will need to install an LOC to make the signal connections. Post...
Forum: Amplified Tube Subwoofers 09-09-2014, 01:28 PM
Replies: 9
Views: 436
Posted By heavyduty
Re: BTA8100 Assistance Needed

Contact Sonic Electronix and ask for a return authorization.
Forum: Amplified Tube Subwoofers 09-09-2014, 01:23 PM
Replies: 1
Views: 156
Posted By heavyduty
Re: Please help identify

That appears to be an A30.

http://www.bazooka.com/tech/wiring-diagrams/A-30

Here is your new harness;
...
Forum: Amplified Tube Subwoofers 09-09-2014, 01:20 PM
Replies: 3
Views: 159
Posted By heavyduty
Re: Consant Even Volume

I responded to your other post inquiring into where the connections were made before I read this post. Can you tell me what wires you connected to at the headunit?
Forum: Amplified Tube Subwoofers 09-09-2014, 01:18 PM
Replies: 3
Views: 299
Posted By heavyduty
Re: Volume Control - Factory 2006 Jeep Radio

Where have the FAST Harness connections been made?
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 11:02 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Template-Modifications by TMS
bazooka.com
SAS, BAZOOKA, BASS TUBES, and LISTEN TO YOUR EARS are registered trademarks of Southern Audio Services, Inc.